RT330 | REVO TURBO UPGRADE | Fiesta ST 2014-2018
NOT ANOTHER HYBRID TURBO.
The ultimate Turbo upgrade option for the Fiesta ST, Only Revo completely redesign the entire compressor and turbine housing to give you a driving experience like no other. Exhilarating top end power coupled with the responsive driveability low down means you get the best of both worlds.
Only Revo Turbos are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock turbo, the RT330 is a high-quality upgrade, precision balanced to levels above OEM specification to improve performance and ensure reliability.
- Bespoke cast compressor and turbine housings
- Optimised compressor and turbine wheels
- Superior flow characteristics
- Capable of 330 HP
- Designed in harmony with Revo Software
- RT330 Turbo Charger
- Complete Fitting Kit
- Charge and throttle pipes
- Intake elbow for Revo Intake
- Intake reducer and coupler for non Revo Intakes
The limitations of the housings on stock turbos means that they can only be machined to a safe thickness to allow a slightly larger compressor and turbine wheel. The issue with running larger wheels in smaller housings is the increase in temperatures, this is one of the biggest issues with the turbine side of ST hybrid turbos. Increasing both wheels allows for a power increase with higher boost pressures, however, they cannot constantly maintain power due to these increases in temperatures.
The Revo RT330 offers a significant upgrade over the stock KP39 turbo, with completely bespoke castings of both the compressor and turbine housings. Without being limited by the OEM turbo housings, superior flow characteristics are achieved by increasing the wheel size, eliminating heat issues and providing constant high performance. The custom turbine housing has been designed specifically for the Fiesta ST and offers a direct OEM fitment.
COMPRESSOR & TURBINE WHEELS
The compressor and turbine wheels have been increased in size, far larger than hybrid options. The stronger construction of the larger compressor wheel, machined from solid billet aluminium, provides a higher air flow capability. The short-bladed KO4 turbine wheel increases exhaust gas flow with a minimal increase in lag over hybrids. The lightweight construction of the wheels ensures low inertia which in turn increases performance.
Strength is the key, an exclusively designed thrust bearing assembly allows for the higher thrust loading requirements of running increased flowrates and boost pressures without compromising on reliability. The K04 frame upgrade incorporates a larger diameter shaft and bearings, which provides increased strength at high power levels. Integrating the recirculation system with swirl-assisting minimises shaft deceleration on gear changes.
THE COMPLETE KIT
No detail has been overlooked when reducing restrictions within the stock airflow system. During development alongside Revo Performance ECU Software, further restrictions were found in the system. To ensure ultimate performance, the RT330 inlet hose has been significantly increased and proves a smoother flow of air directly into the turbo. Increased diameters on the charge and throttle pipes were also designed to increase air flow speed, improving flow at higher levels.
The following testing was carried out on a Ford Fiesta ST running stock engine and fuel system, on Shell Power 99ron Pump fuel. Revo RT330 Turbo Kit, Performance ECU Software installed, fitted with a Revo Air Intake System, Airtec Stage 3 Intercooler and Milltek Turbo back exhaust system with sports Catalytic convertor.
The Revo Turbo offers significant performance gains over any stock turbo setup, with peak gains of up to 158HP and 177NM torque over a stock Fiesta ST, recorded on a Maha Dyno. Compared to the KP38ETR Hybrid setup, the RT330 offers an additional peak gain of 34HP at @ the hubs and 37NM
Upgrading the airflow to and from the Revo RT330 is a key part to achieve the maximum performance, specifically designed products to remove restriction and allow a smoother uninterrupted air flow.
For cars running the Revo Air Intake System, a single piece silicone intake elbow tapers from the intake pipe to the seamlessly stepped neck onto the turbo. The Revo Intake allows for optimum airflow into the turbo without causing unnecessary turbulence and without the need to reduce the inlet size too early. A stepped reducer and machined coupler is also included in the kit to allow fitment of a standard size air intake system.
CHARGE AND THROTTLE PIPES
The Revo turbo kit comes complete with all hoses and replacement charge side pipe as well as an increased sized throttle pipe. The throttle pipe has been added to the kit as it was found that the OE part was too restrictive in the final stages of tuning. The Revo throttle pipe is a single piece mandrel bent aluminium pipe with an increased internal diameter, allowing for better air flow to the throttle body. Designed with all the relative take off’s made from machined aluminium to connect to the OE sensors.
*No discounts codes will be accepted for revo turbo purchases / orders placed with coupon codes will be cancelled
*Price Match - we will make every attempt to price match any US dealer on revo RT330 kits if we are not already the lowest price Message us!